Org VDC System and Network Configuration

This section, describes how to configure the VDC required for HDM deployment.

To perform the configuration steps in this section can take from 30 to 60 minutes

Network Configuration

Step 1: Create Routed Network UPLINK_WAN_NETWORK

This network will be connected to the edge gateway. Cross-WAN communications between on-premises and cloud will be routed through this network for the HDM Appliance. IPsec tunnels step 3 will be configured to this network to complete the network configuration.

  1. Select the Virtual Data Center that will be the target of migration. Select ORG VDC

  2. Select Network -> NEW to create a new network. Create new network
  3. Create a new network and select Routed Network Type alt_text

  4. Provide the name “UPLINK_WAN_NETWORK” and Gateway CIDR for the network. Note the CIDR; this will be required when creating the VPN connection between on-premises and the edge gateway in the cloud. alt_text

  5. Select the edge gateway alt_text

  6. Specify static-ip pool of at least 20 IP addresses alt_text

  7. Add DNS records if required alt_text

  8. Review, then select "Finish" to create the routed network alt_text

Step 2: Create Isolated Network HDM_INTERNAL_NETWORK

This network will be created for HDM Appliance communications and for migrating virtual machines across vApps for the same VDC.

  1. Create a new network and select "Isolated Network Type"

alt_text

  1. Provide the name “HDM_INTERNAL_NETWORK” and Gateway CIDR for the network. Make sure enough IPs are available in the subnet, as this will be used for migrating virtual machines. The network will be assigned during migration and then removed post-migration.

alt_text

  1. Specify static-ip pool or at least 30 IPs.

alt_text

  1. Review, then select "Finish" to create the isolated network

alt_text

Step 3: Configure VPN tunnel with Edge Gateway

Create an IPSec tunnel between the organization's edge gateway and the on-premises datacenter. To complete the VPN setting the following information will be required:

  • Local ID - Edge gateway tenant external network IP (see Figure 1)
  • Local Endpoint - Edge gateway tenant external network IP (see Figure 1)
  • Local Subnets - Routed network subnet where HDM appliances will be deployed (Create Routed Network)
  • Peer ID - Public IP for the on-premises WAN network
  • Peer Endpoint - Public IP for the on-premises WAN network
  • Peer Subnets - Subnet of the on-premises WAN network where HDM appliances will be deployed.

Figure 1: Finding tenant external network IP Find external IP

Edge gateway VPN config

To get to the edge VPN configuration page.

  1. Select the services on the edge gateway. Select services
  2. Select add VPN Select add VPN
  3. Make the settings as recorded earlier. alt_text
  4. For the VPN configuration options make the exact settings as shown in Figure 2 and enter the exactly same values at premises VPN configuration.
    • Encryption Alogrithm: AES256
    • Authentication: PSK
    • Diffie-Hellman Group: DH5
    • Digest Algorithm: SHA-256
    • IKE Option: IKEv2
    • Session Type: Policy Based Session

Figure 2: VPN configuration options VPN configuration options

Recommended firewall rules

Add recommended firewall rule by specifying source and destination subnet with service any

alt_text

Service/Port level requirement for HDM(Advanced firewall rules)

  1. On-premises WAN network - Cloud WAN network ports(Inbound/Outbound): 22, 2379, 32820, 2376, 6000-6050, 7000-7050, 8000-8050.

alt_text

alt_text

You can test the IPsec connectivity using ping command from on-premises to cloud side routed network gateway. If you have configured advanced firewall rules, ensure that ICMP traffic is allowed.

Ping test from on-premises to the cloud gateway

alt_text

To ping test from the cloud to the on-premises IP, a test machine will need to be created on the routed network in the cloud.

alt_text

System Configuration

Configure vApp for HDM Deployment

The components of HDM need to be deployed on a vApp. If you don’t already have a vApp for this purpose, one will need to be created.

Attach the VDC network UPLINK_WAN_NETWORK and HDM_INTERNAL_NETWORK, both of which were created in steps 1 and 2, to the vApp where HDM will be deployed.

NOTE: HDM_INTERNAL_NETWORK should be added to all vApps where VMs will be migrated.

alt_text